Fiber Converters
Quick Installation Guide (1)
Fiber Converters /10.30.2012
2. Hardware Installation
Installing Two Stand Alone Fiber Converters Together
1. Connect an RJ-45 Ethernet cable from the Ethernet port on the fiber converters to an Ethernet
port on your switch (e.g TE100-S24g).
2. Connect the fiber cable to the fiber converters.
3. Connect the power adapter to the fiber converter.
Note:
For the TFC-110MM/MST/MSC/110S15/S15i/S30/S30i/S60/S60i/S100, the TX and RX cables
must be reversed on the opposite fiber connection
TFC-15MS100 converts Multi-Mode to Single-Mode fiber, it can be connected to a switch with
Multi-Mode SC-type fiber connection (e.g TEG-424WS with fiber modules) to extend the distance
up to 15km with Single-Mode fiber.
Cabling
• Multi-Mode Fiber Optic Cable: TFC-110MSC, TFC-110MST, TFC-110MM
• Single-Mode Fiber Optic Cable: TFC-110S15, TFC-110S30, TFC-110S60, TFC-110S100,
TFC-110S15i, TFC-110S30i, TFC-110S60i
• Single Strand Fiber Optic Cable: TFC-110S20D3, TFC-110S20D5, TFC-110S20D3i,
TFC-110S20D5i, TFC-110S40D3i, TFC-110S40D5i
2
Installing Fiber Converter in a Chassis
1. Unscrew the bay cover from the desired bay on the chassis.
2. Unfasten the thumbscrew and remove the fiber converter from the metal casing.
3. Slide the fiber converter into an available slot and fasten the thumbscrew.
3
3. LEDs and DIP switches
LED
Color
Sequence Function
TFC-110MM/MST/MSC/
TFC-110S15i/30i/60i
TFC-15MS100
110S15/S30/S60/S100/20D3/
S20D5/20D3i/20D5i/40D3i/
40D5i
Device powered On
Device powered Off
Green
N/A
Solid
Off
PWR
(Power)
100/200Mbps (Half/Full Duplex) Connection
10/20Mbps (Half/Full Duplex) Connection
Connection on TX end in full duplex mode
Green
Solid
N/A
100M
N/A
Off
N/A
Green
Solid
Blinking
N/A
N/A
N/A
N/A
N/A
N/A
FDX / COL
(TX)
Green
N/A
Data collision is detected
Connection on TX end in half duplex mode
Connection on Fiber end in full duplex mode
Data collision is detected
Off
Green
Green
N/A
Solid
Blinking
Off
FDX / COL
(FX)
Connection on Fiber end in half duplex mode
100/200Mbps (Half/Full Duplex)
or 10/20Mbps (Half/Full Duplex) Connection
Green
Green
Solid
N/A
LINK/ACT
(TX)
100/200Mbps (Half/Full Duplex)
or 10/20Mbps Data Transmitting/Receiving
Blinking
N/A
N/A
Off
The link is disconnected
N/A
100/200Mbps (Half/Full Duplex) Connection
Green
Solid
Blinking
Off
N/A
LINK/ACT
(FX)
100/200Mbps (Half/Full Duplex) Data Transmitting/Receiving
The link is disconnected
Green
N/A
N/A
N/A
100/200Mbps (Half/Full Duplex)
Connection
Green
Green
N/A
Solid
N/A
LINK/ACT
100/200Mbps (Half/Full Duplex)
Data Transmitting/Receiving
Blinking
N/A
N/A
The link is disconnected
N/A
Red
N/A
Off
N/A
N/A
N/A
N/A
The TX link is disconnected
Solid
Off
FAIL (TX)
FAIL(FX)
N/A
N/A
N/A
The TX link is connected
The Fiber link is disconnected
The Fiber link is connected
N/A
N/A
N/A
Red
Solid
Off
N/A
4
Switch
Action
Function
TFC-110MM/MST/MSC/
110S15/S30/S60/S100
TFC-110S15i/30i/60i/20D3i/20D5i/40D3i/40D5i
Half-Duplex
Full-Duplex
N/A
Fiber Half-Duplex
Fiber Full-Duplex
TX Forced Mode
TX Auto-Negotiation
On
1
2
3
4
5
6
Off
On
Off
N/A
On
Off
On
Off
N/A
TX 10M
N/A
TX 100M
TX Half-Duplex
TX Full Duplex
N/A
N/A
On
Off
On
Off
N/A
N/A
N/A
N/A
LLR Enable
LLR Disable
LLR Enable
LLR Disable
Note:
After changing the DIP Switch settings, power cycle the Fiber Converter.
LLCF stands for Link Loss Carry Forward. When LLCF is enabled, the ports do not transmit a link
signal until they receive a link signal from the opposite port. Link loss is “carried forward” to the
managed switch or hub that is sending the link. LLCF can be used for either the copper or fiber
ports.
LLR stands for Link Loss Return. When LLR is enabled, the fiber port’s transmitter shuts down if
its receiver fails to detect a valid receive link. If one of the optical conductors is bad, the card with
LLR enabled will return a no link condition to its link partner. LLR is used to detect link problems
only on the fiber port. If LLR is enabled on one Fiber converter, the opposite Fiber converter must
have LLR disabled.
5
4. Technical Specifications
Power Budget
Optical Output Power Optical Input Power
Model Name
Media
Connectors
Wavelength
Power Distance
Budget
(dBm)
(dBm)
(dBm)
Min.
Max.
Min.
(Sensitivity)
Max.
Transmit
(TX)
Receive
(RX)
TFC-110MSC
MMF
(Multi-mode
fiber)
RJ-45/SC (Duplex)
1300nm
-19
14
-32
-14
13
13
2km
TFC-110MST
TFC-110MM
MMF
MMF
RJ-45/ST (Duplex)
1300nm
1300nm
-19
14
14
-32
-14
2km
-23.5
-31
-33.5 (typ.) 7.5
2km
RJ-45/MT- RJ
(Duplex)
TFC-110S15
SMF
RJ-45/SC (Duplex)
1310nm
-20
0
-32
0
12
15km
(Single-mode
fiber)
TFC-110S30
TFC-110S60
SMF
SMF
RJ-45/SC (Duplex)
RJ-45/SC (Duplex)
RJ-45/SC (Duplex)
1310nm
1310nm
1550nm
-15
-5
-8
0
-34
-35
-35
0
0
0
19
30
30
30km
60km
100km
TFC-110S100 SMF
-5
0
TFC-110S15i
TFC-110S30i
TFC-110S60i
SMF
SMF
SMF
RJ-45/SC (Duplex)
1310nm
1310nm
1310nm
-20
-15
-5
0
-32
-34
-35
-31
-31
-31
0
0
0
0
0
0
12
19
30
17
17
17
15km
30km
60km
20km
20km
20km
RJ-45/SC (Duplex)
-8
0
RJ-45/SC (Duplex)
TFC-110S20D3 SMF
RJ-45/SC (Simplex) 1310nm
1550nm -14
-8
-8
-8
1550nm
RJ-45/SC (Simplex) 1310nm
RJ-45/SC (Simplex)
1310nm -14
RJ-45/SC (Simplex)
TFC-110S20D5 SMF
TFC-110S20D3i SMF
1550nm -14
TFC-110S20D5i SMF
TFC-110S40D3i SMF
TFC-110S40D5i SMF
1550nm
1310nm -14
1550nm -8
1310nm -8
-8
-3
-31
-34
0
17
26
20km
40km
RJ-45/SC (Simplex) 1310nm
-3
RJ-45/SC (Simplex) 1550nm
SC (Duplex)
-3
-14
0
-34
-31
-32
-3
0
26
7.5
12
40km
2km
MMF (1)
SMF (2)
1300nm
1310nm
-23.5
-20
TFC-15MS100
SC (Duplex)
0
15km
6
TFC-110MSC,ꢀTFC-110MST,ꢀTFC-110MM,ꢀTFC-15MS100,ꢀTFC-110S15,ꢀ
TFC-110S30,ꢀTFC-110S60,ꢀTFC-110S100,ꢀTFC-110S15i,ꢀꢀTFC-110S30i,ꢀꢀ
TFC-110S60i,ꢀꢀTFC-110S20D3,ꢀTFC-110S20D5,ꢀTFC-110S20D3i,ꢀ
TFC-110S20D5i,ꢀTFC-110S40D3i,ꢀTFC-110S40D5i,ꢀꢀTFC-15MS100
GPL/LGPL General Information
This TRENDnet product includes free software written by third party developers. These codes are subject to the GNU General Public
License ("GPL") or GNU Lesser General Public License ("LGPL"). These codes are distributed WITHOUT WARRANTY and are subject
to the copyrights of the developers. TRENDnet does not provide technical support for these codes. The details of the GNU GPL and
LGPL are included in the product CD-ROM.
years from the product shipping date.
You could also request the source codes by contacting TRENDnet.
20675 Manhattan Place, Torrance, CA 90501, USA. Tel: +1-310-961-5500 Fax: +1-310-961-5511
Informations générales GPL/LGPL
Ce produit TRENDnet comprend un logiciel libre écrit par des programmeurs tiers. Ces codes sont sujet à la GNU General Public
License ("GPL" Licence publique générale GNU) ou à la GNU Lesser General Public License ("LGPL" Licence publique générale limitée
GNU). Ces codes sont distribués SANS GARANTIE et sont sujets aux droits d'auteurs des programmeurs. TRENDnet ne fournit pas
d'assistance technique pour ces codes. Les détails concernant les GPL et LGPL GNU sont repris sur le CD-ROM du produit.
spécifiques de chaque licence.
Les codes source sont disponibles au téléchargement sur le site Internet de TRENDnet web site
Vous pouvez également demander les codes source en contactant TRENDnet.
20675 Manhattan Place, Torrance, CA 90501, USA. Tel: +1-310-961-5500 Fax: +1-310-961-5511
Allgemeine Informationen zu GPL/LGPL
„Linux „mtd“ (Memory Technology Devices) Implementation (© 2000 David Woodhouse), erstmals integriert in Linux Version 2.4.0-test 3
haben durch den Erwerb dieses Produktes keinerlei Gewährleistungsansprüche gegen die Berechtigten an der oben genannten
Software erworben; weil diese die Software kostenfrei lizenzieren gewähren sie keine Haftung gemäß unten abgedruckten
Lizenzbedingungen. Die Software darf von jedermann im Quell-und Objektcode unter Beachtung der Lizenzbedingungen der GNU
General Public License Version 2, und GNU Lesser General Public License (LGPL) vervielfältigt, verbreitet und verarbeitet werden.
Die Lizenz ist unten im englischsprachigen Originalwortlaut wiedergegeben. Eine nichtoffizielle Übersetzung in die deutsche Sprache
auf der mitgelieferten CD-ROM.
Downloads verfügen können Sie bei TRENDnet.
20675 Manhattan Place, Torrance, CA 90501 -U.S.A -, Tel.: +1-310-961-5500, Fax: +1-310-961-5511 die Software anfordern.
Información general sobre la GPL/LGPL
Este producto de TRENDnet incluye un programa gratuito desarrollado por terceros. Estos códigos están sujetos a la Licencia
pública general de GNU (“GPL”) o la Licencia pública general limitada de GNU (“LGPL”). Estos códigos son distribuidos SIN
GARANTÍA y están sujetos a las leyes de propiedad intelectual de sus desarrolladores. TRENDnet no ofrece servicio técnico
para estos códigos. Los detalles sobre las licencias GPL y LGPL de GNU se incluyen en el CD-ROM del producto.
específicas de cada licencia.
Los códigos fuentes están disponibles para ser descargados del sitio Web de TRENDnet
También puede solicitar el código fuente llamando a TRENDnet.
20675 Manhattan Place, Torrance, CA 90501, USA. Tel: +1-310-961-5500 Fax: +1-310-961-5511
Общая информация о лицензиях GPL/LGPL
В состав данного продукта TRENDnet входит бесплатное программное обеспечение, написанное сторонними разработчиками.
Это ПО распространяется на условиях лицензий GNU General Public License ("GPL") или GNU Lesser General Public License
("LGPL"). Программы распространяются БЕЗ ГАРАНТИИ и охраняются авторскими правами разработчиков. TRENDnet не
оказывает техническую поддержку этого программного обеспечения. Подробное описание лицензий GNU GPL и LGPL можно
найти на компакт-диске, прилагаемом к продукту.
В пунктах (http://www.gnu.org/licenses/gpl.txt) и (http://www.gnu.org/licenses/lgpl.txt) изложены конкретные условия каждой из
лицензий.
Исходный код программ доступен для загрузки с веб-сайта TRENDnet (http://trendnet.com/downloads/list_gpl.asp) в течение, как
минимум, трех лет со дня поставки продукта.
Кроме того, исходный код можно запросить по адресу TRENDnet.
20675 Manhattan Place, Torrance, CA 90501, USA. Tel: +1-310-961-5500 Fax: +1-310-961-5511
GPL/LGPL informações Gerais
Este produto TRENDnet inclui software gratuito desenvolvido por terceiros. Estes códigos estão sujeitos ao GPL (GNU General Public
License) ou ao LGPL (GNU Lesser General Public License). Estes códigos são distribuídos SEM GARANTIA e estão sujeitos aos
direitos autorais dos desenvolvedores. TRENDnet não presta suporte técnico a estes códigos. Os detalhes do GNU GPL e do LGPL
específicos de cada licença.
menos três anos da data de embarque do produto.
Você também pode solicitar os códigos fonte contactando TRENDnet, 20675 Manhattan Place, Torrance, CA 90501, USA.Tel: +1-310-
961-5500, Fax: +1-310-961-5511.
GPL/LGPL üldinformatsioon
See TRENDneti toode sisaldab vaba tarkvara, mis on kirjutatud kolmanda osapoole poolt. Koodid on allutatud GNU (General Public
License) Üldise Avaliku Litsentsi (GPL) või GNU (Lesser General Public License) ("LGPL") Vähem Üldine Avalik Litsentsiga. Koode
vahendatakse ILMA GARANTIITA ja need on allutatud arendajate poolt. TRENDnet ei anna koodidele tehnilist tuge. Detailsemat infot
GNU GPL ja LGPL kohta leiate toote CD-ROMil. Infot mõlema litsentsi spetsiifiliste terminite kohta leiate
alates toote kättesaamise kuupäevast.
Samuti võite lähtekoodi paluda TRENDneti'lt, 20675 Manhattan Place, Torrance, CA 90501, USA. Tel: +1-310-961-5500, Fax: +1-310-
961-5511.
Fiber Converters
Fiber Converters /10.30.2012
Fiber Converters
Fiber Converters /10.30.2012
|